I am looking to relocate my outdoor heat pump, gas, service, and electrical service/meter all to a pad that is approximately 20 feet off the side of my house. Because of the coordination required between HVAC, plumbing, and electrical, I’d like a base set of drawings that can, show how this should be configured. The line set, gas line, and electrical service, will be buried to the house. The home is in Kansas, and the set of drawings will need to be approved by our local code office. The selected designer for this system Should be able to help us meet 2021 IRC codes which is what our city uses I believe. We can confirm this once hired. Does not need to be complex by any means. The main point of having the drawings as simply just to keep all of the various contractors on the same page.

Evaluate existing commercial kitchen hood equipment, review new cooking equipment, and determine if the existing hood will work for the new equipment. Preferred to be located in Southern California.

Looking for someone to design a simple and eye-catching tri-fold brochure for an HVAC contractor. I have the content, I need someone to place it and make it branded.

Looking for HVAC Designer to provide on going services: Manual J Load Calculations Manual S system sizing calculations Manual D duct design CAD drawings Equipment Schedules PE is preferable but not required. Work directly with company principle, no intermediaries. Principle has over 30 years HVAC Industry / Construction experience. Looking for someone who values details, colaboration and teamwork to meet project objectives. To make the best use of everyone's time, deliverables will be clearly identified and agreed to for each individual project. Majority of projects are large residential properties, new and renovation work. Project size, scope and complexity varies from project to project. Opportunity for 1-2 projects per month.

The floor plan is attached. I need to add a sink in the shop area near the bathroom, a hose bib near the main garage drain and a washer/dryer connection and floor drain in the mechanical room. I am looking for a simple plan that is easy to self perform. My jurisdiction uses 2018 UPC. Thank you.

We are installing a Hobart Commercial Oven in a production bakery. Our building inspector is requiring engineering plans before our HVAC contractor can begin work. The oven is in place and electrical has been run to it. Natural gas hookup and ductwork are required. Project is based in Minnesota.

Hello - We submitted our home addition plans to the village and they came back asking for a grading plan (please see screenshot attached), including a topographic plan. Our address is 206 Green Bay Rd in Winnetka. I've also attached the construction drawings. Also, please let me know if you have licensed in Illinois. Thank you, Christine

HVAC design for a residential project. High eff. Heat Pump with Propane Back-up, Electrical design with optimal locations for switch board, Design with maximum concealed duct work and cables. Please respond with your hourly rate and contact number. Plumbing design to connect with septic system.

Bluefield Engineering will perform all of the engineering and design, producing SD, DD, and CD sets for the client. The entire project will be subjected to our internal quality control process. We have designed 5 prior/similar Semi Maintenance and Body Shop facilities for the same client in Utah--that are all operating satisfactorily. We are therefore not concerned with the freelance stamping engineer being fully competent in this niche. Our work will be largely confined to typical radiant tube and unit heat and mini-split and RTU solutions in the office areas. The Permit set will need to be reviewed and stamped by a Licensed PE in Idaho. This PE freelancer will need to be fully competent or fluent in Revit and BIM360 (soon ACC). This project is a one-off, but we have two more current projects in Idaho that will need a similar cooperative relationship. While these will be listed as separate job postings in Upwork, we would prefer to work with one competent PE for all three and future projects in Idaho.

Bluefield Engineering will perform all of the engineering and design, producing SD, DD, and CD sets for the client. The entire project will be subjected to our internal quality control process. We have designed 3 prior/similar Mill/Office/Truss facilities for the same client in Utah--that are all operating satisfactorily. We are therefore not concerned with the freelance stamping engineer being fully competent in this niche. Our work will be largely confined to typical radiant tube and unit heat and mini-split and RTU solutions in the office. The Permit set will need to be reviewed and stamped by a Licensed PE in Idaho. This PE freelancer will need to be fully competent or fluent in Revit and BIM360 (soon ACC). This project is a one-off, but we have two more current projects in Idaho that will need a similar cooperative relationship. While these will be listed as separate job postings in Upwork, we would prefer to work with one competent PE for all three and future projects in Idaho.